In any hydraulic circuit there are slight variations in presence of oil. When pressure changes the rate of flow changes but many circuits requires constant flow regardless of input or output pressure variations in the circuit then the pressure compensated FCV is used. It consists of hollow cylinder shaped poppet at the bottom of which there is a fixed orifice. There is a spring inside a poppet as shown in fig.
makes available to the system whenever required. Necessity of accumulator for every huge hydraulic press: Oil requirement of the system is not continuous but intermittent. A hydraulic press needs the oil only during the lifting operation. While, during the lowering of load, holding the load or during idle period, it doesn’t not require any supply of oil. During such period, the hydraulic pump has to stop or delivered oil must be drained back to the sump. But frequent starting and stopping of pump is not desirable as it reduces the pump life.
It’s an inclined plate in axial piston pump on which all pistons are connected through piston rod. This swash plate is usually inclined. Use – It is helps to reciprocate the piston of axial piston pump while the cylinder block is rotating Working: Motor drives the shaft, which in turn rotates the entire cylinder block. The pistons are connected to inclined swash plate through piston rod. Now since swash plate is inclined and block is rotating, the piston reciprocates inside the barrel.
Draw and explain working of pressure reducing valve. The main function of pressure reducing valve is to reduce the pressure in particular branch of the circuit to different level as demanded by consumer in that branch. Construction: It consists of spool and spring housed in the bore of valve body. Spring compression can be adjusted by pressure setting screw. Port P is pressure port connected to pump. Port A is consumer port requiring reduced pressure.
What is function of (i) Oil Reservoir – To store the Hydraulic oil for the circuit (ii) Pressure Relief Valve- To release the extra pressure whenever not required by system (iii) Direction Control Valve- To give the direction to the actuator (iv) Filters- To filter the foreign particle from the oil and to separates sub-micron level contamination
Strength equation of double parallel fillet weld= throat area x allowable shear stress P= 2x 0.707x Sw x lwx Ʈ =1.414 x Sw x lwx Ʈ (1mark) Strength equation of single transverse fillet weld
P =throat area x allowable tensile stress P= 0.707x Sw x lw x σ
Rolling contact bearing- contact between the surfaces is rolling ,it is antifriction bearing Advantages (any six) (1)low starting and running friction except at very high speed (2) ability to withstand momentary shock loads (3) accuracy of shaft alignment (4) low cost of maintenance (5) reliability of service (6) easy to mount and erect (7) cleanliness (8) small overall dimension
Horizontal component of 45 KN, WH= 45Sin 600 =45x 0.866=38971N and vertical component of 45 KN, Wv,= 45xcos600 =45x0.5=22500N Direct tensile load in each bolt,Wt1= WH /5=38971/5=7794.20N Turning moment due to WH about G TH = WHx 25=38971x25=974275N (anticlockwise) direct shear load on each bolt =Ws=Wv/5 =22500/5=4500N Turning moment due to Wv about edge of the bracket, Tv= Wvx175=22500x175=3937500N-mm( clockwise( clockwise) Net turning moment =3937500-974275=2963225N---------(I) total moment of the load on the bolts @ th tilting edge = 2w x(L1) 2 + 2w x(L2) 2 =2xwx(50)2 + 2xwx(150)2 = 50000
given load W= 135N Deflection ᵟ =7.5mm Spring index c=10 Permissible shear stress Ʈ=480 MPa Modulus of rigidity G =80 KN/mm2 Wahl’s factor K =4C-1/4C-4 +0.615/C=4X10-1/4X10-4 +0.615/10=1.14 (1)Mean dia. Of the spring coil (1 mark) Maximum shear stress, Ʈ = Kx 8WC/π d 2 480 = 1.14x 8x135x10/3.142xd2 d = 2.857mm from table we shall take a standard wire of size SWG 3 having diameters (d) =2.946mm mean dia. Of the spring coil D= CXd =10x2.946=29.46 mm outer dia.
